Have you been hunting for resources around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough task. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. Ensure you have actually qualified on your own for the task and are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is far better to consider using one before you start. Chances are you may require an expert plumber to make tube links.
This write-up will assist you install a new bath tub in your restroom if you have actually already gotten a brand-new tub and also don't need to transform the arrangement of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite troublesome as a result of the restricted access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipelines have actually been eliminated, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Protect the tap in place with the producer provided backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap adapters. The previous type ought to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using both wood boards under its feet, put the tub in the required placement. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill the tub as well as likewise examine the overflow outlet and also the normal outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its last setting.
Planning for the Setup
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture an inflexible seal, creating the water to pass through the wall in between the bath as well as the tiling, causing issues with moisture as well as feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealer can break fairly very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very inquisitive about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am praying you enjoyed my piece. In case you enjoyed reading our blog post kindly make sure you remember to pass it around. Thanks a bunch for your time. Kindly stop by our site back soon.
Detail